Cincinnati
(800) 736-3524
Columbus
(800) 784-1475
Lexington
(800) 844-2768
Louisville
(844) 287-3883

Hand-held Router Bits

View as Grid List
Sort by

Amana Tool ® 45190 Straight Plunge High Production 1/16 Dia x 3/16 x 1/4 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced. 45190 features a solid carbide cutting edge.

Amana Tool ® 45200 Straight Plunge High Production 1/8 Dia x 7/16 x 1/4 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced. 45200 features a solid carbide cutting edge.

Amana Tool ® 45202 Straight Plunge High Production 3/16 Dia x 7/16 x 1/4 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced. 45202 features a solid carbide cutting edge.

Amana Tool ® 45208 Carbide Tipped Straight Plunge High Production 1/4 Dia x 3/4 x 1/4 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45210 Carbide Tipped Straight Plunge High Production 1/4 Dia x 1 Inch x 1/4 Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45211 Carbide Tipped Straight Plunge High Production 1/4 Dia x 1 Inch x 1/4 Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45218 Carbide Tipped Straight Plunge High Production 3/8 Dia x 1 Inch x 1/4 Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45226 Carbide Tipped Straight Plunge High Production 1/2 Dia x 1 Inch x 1/4 Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45228 Carbide Tipped Straight Plunge High Production 5/8 Dia x 3/4 x 1/4 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45230 Carbide Tipped Straight Plunge High Production 3/4 Dia x 3/4 x 1/4 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45414 Carbide Tipped Straight Plunge High Production 3/8 Dia x 1 Inch x 1/2 Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45418 Carbide Tipped Straight Plunge 1/2 Dia x 1 Inch x 1/2 Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45420 Carbide Tipped Straight Plunge 1/2 Dia x 1-1/4 x 1/2 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45422 Carbide Tipped Straight Plunge 1/2 Dia x 1-1/2 x 1/2 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45426 Carbide Tipped Straight Plunge 1/2 Dia x 2 Inch x 1/2 Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45427 Carbide Tipped Straight Plunge 1/2 Dia x 2-1/2 x 1/2 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45445 Carbide Tipped Undersized Plywood Dado Plunge 23/32 Dia x 1-1/4 x 1/2 Inch Shank for Plywood Thickness 3/4 minus 1/32

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45448 Carbide Tipped Straight Plunge High Production 1 Inch Dia x 1-1/4 x 1/2 Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45460 Carbide Tipped Flush Trim Plunge Template 1/2 Dia x 1 Inch x 1/4 Shank with Upper BB

This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile, useful for template/pattern routing of parts, joints, internal cuts and can be used in handheld and table-mounted routers. The template is attached to the workpiece, and the pilot bearing rides along its edge as the cutting edges rout the workpiece, forming an exact duplicate of the template. With a handheld router, the pattern is on top of the work; with a table-mounted router, the pattern is underneath the work.

Amana Tool ® 45460-S Carbide Tipped Dado Clean Out 1/2 Dia x 1/4 x 1/4 Inch Shank with Upper BB

Bits are designed with a 1/4" cutting edge for dado clean-out. Also used in hardwood and flooring medallions.

Amana Tool ® 45461 Carbide Tipped Flush Trim Plunge Template 1/2 Dia x 1-1/4 x 1/4 Inch Shank with Upper BB

This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile, useful for template/pattern routing of parts, joints, internal cuts and can be used in handheld and table-mounted routers. The template is attached to the workpiece, and the pilot bearing rides along its edge as the cutting edges rout the workpiece, forming an exact duplicate of the template. With a handheld router, the pattern is on top of the work; with a table-mounted router, the pattern is underneath the work.

Amana Tool ® 45462 Carbide Tipped Flush Trim Plunge Template 5/8 Dia x 1 Inch x 1/4 Shank with Upper BB

This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile, useful for template/pattern routing of parts, joints, internal cuts and can be used in handheld and table-mounted routers. The template is attached to the workpiece, and the pilot bearing rides along its edge as the cutting edges rout the workpiece, forming an exact duplicate of the template. With a handheld router, the pattern is on top of the work; with a table-mounted router, the pattern is underneath the work.

Amana Tool ® 45464 Carbide Tipped Flush Trim Plunge Template 3/4 Dia x 1 Inch x 1/4 Shank with Upper BB

This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile, useful for template/pattern routing of parts, joints, internal cuts and can be used in handheld and table-mounted routers. The template is attached to the workpiece, and the pilot bearing rides along its edge as the cutting edges rout the workpiece, forming an exact duplicate of the template. With a handheld router, the pattern is on top of the work; with a table-mounted router, the pattern is underneath the work.

Amana Tool ® 45465 Carbide Tipped Flush Trim Plunge Template 3/4 Dia x 1-3/4 x 1/2 Inch Shank with Upper BB

This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile, useful for template/pattern routing of parts, joints, internal cuts and can be used in handheld and table-mounted routers. The template is attached to the workpiece, and the pilot bearing rides along its edge as the cutting edges rout the workpiece, forming an exact duplicate of the template. With a handheld router, the pattern is on top of the work; with a table-mounted router, the pattern is underneath the work.

Amana Tool ® 45467 Carbide Tipped Flush Trim Plunge Template 1 Inch Dia x 1-3/4 x 1/2 Shank with Upper BB

This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile, useful for template/pattern routing of parts, joints, internal cuts and can be used in handheld and table-mounted routers. The template is attached to the workpiece, and the pilot bearing rides along its edge as the cutting edges rout the workpiece, forming an exact duplicate of the template. With a handheld router, the pattern is on top of the work; with a table-mounted router, the pattern is underneath the work. Maximum RPM 20,000.

Amana Tool ® 45468 Carbide Tipped Flush Trim Plunge Template 1-1/8 Dia x 1-1/2 x 1/2 Inch Shank with Upper BB

This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile, useful for template/pattern routing of parts, joints, internal cuts and can be used in handheld and table-mounted routers. The template is attached to the workpiece, and the pilot bearing rides along its edge as the cutting edges rout the workpiece, forming an exact duplicate of the template. With a handheld router, the pattern is on top of the work; with a table-mounted router, the pattern is underneath the work. Maximum RPM 20,000.

Amana Tool ® 45500 Carbide Tipped Mortising 1/2 Dia x 3/4 x 1/4 Inch Shank

Cutting mortises for hinges and locks can be challenging; the mortise depth must be accurate for smooth operation and the edges must be sharp for a clean, professional installation. These mortise bits make hardware installation a snap. The large gullet between the two flutes clears chips away quickly and the cutter geometry creates a crisp outline for a perfect fit.

Amana Tool ® 45502 Carbide Tipped Mortising 5/8 Dia x 3/4 x 1/4 Inch Shank

Cutting mortises for hinges and locks can be challenging; the mortise depth must be accurate for smooth operation and the edges must be sharp for a clean, professional installation. These mortise bits make hardware installation a snap. The large gullet between the two flutes clears chips away quickly and the cutter geometry creates a crisp outline for a perfect fit.

Amana Tool ® 45700 Carbide Tipped V Groove 90 Deg x 3/8 Dia x 7/16 x 1/4 Inch Shank

Cut decorative "V" grooves and lettering on signs with this 'V' Groove bit. Use with an edge guide to chamfer and bevel edges. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45704 Carbide Tipped V Groove 90 Deg x 1/2 Dia x 1/2 x 1/4 Inch Shank

Cut decorative "V" grooves and lettering on signs with this "V" Groove bit. Use with an edge guide to chamfer and bevel edges. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45705 Carbide Tipped V Groove 60 Deg x 1/2 Dia x 5/8 x 1/4 Inch Shank

Cut decorative "V" grooves and lettering on signs with this "V" Groove bits. Use with an edge guide to chamfer and bevel edges. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45730 Carbide Tipped V Groove Signmaking & Lettering 60 Deg x 9/16 Dia x 7/16 x 1/4 Inch Shank

Originally developed in Europe specifically for professional signmakers, this solid-carbide bit features an extra-fine 60° point that produces a clean, precise cut. For those intricate lines, this bit is superior to standard "V" groover. Makes crisp, clean cuts in solid woods, MDF and acrylics.

Amana Tool ® 45750 Carbide Tipped V Groove 90 Deg x 1/2 Dia x 1/2 x 1/4 Inch Shank with Upper BB

Designed for fluting and 'V' grooving cuts guided by a template or pattern. The shank-mounted ball-bearing pilot rides along the template edge, and the cutter duplicates the template contour in the work piece. With a handheld router, the template must be on top of the work piece. With a table-mounted router, the template must be on bottom of the work piece. 90° ‘V’ Groove bit is for decorative purposes and is not intended for ‘miter-folding’, etc.

Amana Tool ® 45804 Carbide Tipped Dovetail 14 Deg x 1/2 Dia x 1/2 x 1/4 Inch Shank

The 14° dovetail bit is used with common half-blind dovetail jigs, as well as with Omnijig®, Incra® and Leigh® jigs.

Amana Tool ® 45806 Carbide Tipped Dovetail 14 Deg x .532 Dia x 1/2 x 1/2 Inch Shank for Omnijig & Incra

The 14° dovetail bit is used with common half-blind dovetail jigs, as well as with Omnijig®, Incra® and Leigh® jigs.

Amana Tool ® 45904 Carbide Tipped Core Box 1/8 Radius x 1/4 Dia x 1/4 x 1/4 Inch Shank

Cut half-round grooves for fluted moldings, columns, millwork and signs using a core box bit. Used with an edge guide, it can cut coves. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45906 Carbide Tipped Core Box 3/16 Radius x 3/8 Dia x 1/4 x 1/4 Inch Shank

Cut half-round grooves for fluted moldings, columns, millwork and signs using a core box bit. Used with an edge guide, it can cut coves. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45910 Carbide Tipped Core Box 1/4 Radius x 1/2 Dia x 3/8 x 1/4 Inch Shank

Cut half-round grooves for fluted moldings, columns, millwork and signs using a core box bit. Used with an edge guide, it can cut coves. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45918 Carbide Tipped Core Box 3/8 Radius x 3/4 Dia x 7/16 x 1/4 Inch Shank

Cut half-round grooves for fluted moldings, columns, millwork and signs using a core box bit. Used with an edge guide, it can cut coves. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45920 Carbide Tipped Core Box 3/8 Radius x 3/4 Dia x 7/16 x 1/2 Inch Shank

Cut half-round grooves for fluted moldings, columns, millwork and signs using a core box bit. Used with an edge guide, it can cut coves. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45924 Carbide Tipped Core Box 1/2 Radius x 1 Inch Dia x 5/8 x 1/4 Shank

Cut half-round grooves for fluted moldings, columns, millwork and signs using a core box bit. Used with an edge guide, it can cut coves. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45950 Carbide Tipped Core Box 1/4 Radius x 1/2 Dia x 3/8 x 1/4 Inch Shank with Upper BB

Designed for fluting and 'V' grooving cuts guided by a template or pattern. The shank-mounted ball-bearing pilot rides along the template edge, and the cutter duplicates the template contour in the work piece. With a handheld router, the template must be on top of the work piece. With a table-mounted router, the template must be on bottom of the work piece.

Amana Tool ® 46102 Solid Carbide Spiral Plunge 1/4 Dia x 3/4 x 1/4 Inch Shank Up-Cut

Spiral-flute bits combine a shearing action in cutting with an augering action in chip clearance. The shearing action yields an especially clean, accurate cut, while the augering action clears chips from the cut. The ‘Up-Cut’ shears from the bottom up, pulling chips from the bottom up, thus allowing deeper penetration with less stress on the tool. An excellent choice for mortising. Special unique carbide grade, increased clearance geometry and razor-sharp cutting edges with polished flutes, provide a superior finish and longer tool life, especially in abrasive materials. Great for production settings and excellent for creating grooves and dado cuts in particleboard, plywood and laminate. Primarily used on CNC machines and other automatic routers. Can be used with handheld and table-mounted portable routers.

Amana Tool ® 46106 Solid Carbide Spiral Plunge 1/2 Dia x 1-1/4 x 1/2 Inch Shank Up-Cut

Spiral-flute bits combine a shearing action in cutting with an augering action in chip clearance. The shearing action yields an especially clean, accurate cut, while the augering action clears chips from the cut. The ‘Up-Cut’ shears from the bottom up, pulling chips from the bottom up, thus allowing deeper penetration with less stress on the tool. An excellent choice for mortising. Special unique carbide grade, increased clearance geometry and razor-sharp cutting edges with polished flutes, provide a superior finish and longer tool life, especially in abrasive materials. Great for production settings and excellent for creating grooves and dado cuts in particleboard, plywood and laminate. Primarily used on CNC machines and other automatic routers. Can be used with handheld and table-mounted portable routers.

Amana Tool ® 46202 Solid Carbide Spiral Plunge 1/4 Dia x 3/4 x 1/4 Inch Shank

Spiral-flute bits combine a shearing action in cutting with an augering action in chip clearance. The shearing action yields an especially clean, accurate cut, while the augering action clears chips from the cut. The ‘Down-Cut’ cuts from the surface down, leaving a smooth edge at the surface. Special unique carbide grade, increased clearance geometry and razor-sharp cutting edges with polished flutes, provide a superior finish and longer tool life, especially in abrasive materials. Great for production settings and excellent for creating grooves and dado cuts in particleboard, plywood and laminate. Primarily used on CNC machines and other automatic routers. Can be used with handheld and table-mounted portable routers.

Amana Tool ® 46206 Solid Carbide Spiral Plunge 1/2 Dia x 1-1/4 x 1/2 Inch Shank Down-Cut

Spiral-flute bits combine a shearing action in cutting with an augering action in chip clearance. The shearing action yields an especially clean, accurate cut, while the augering action clears chips from the cut. The ‘Down-Cut’ cuts from the surface down, leaving a smooth edge at the surface. Special unique carbide grade, increased clearance geometry and razor-sharp cutting edges with polished flutes, provide a superior finish and longer tool life, especially in abrasive materials. Great for production settings and excellent for creating grooves and dado cuts in particleboard, plywood and laminate. Primarily used on CNC machines and other automatic routers. Can be used with handheld and table-mounted portable routers.

Amana Tool ® 46300 Solid Carbide UltraTrim Spiral 1/2 Dia x 1-1/4 x 1/2 Inch Shank with Double Lower Ball Bearing Up-Cut

For the ultimate, chip-free finish in laminate, melamine, solid surface, fragile veneers and for template work of all kinds. The twin ball-bearing pilot enhances the stability of the tool. Available in 'Up-Cut' and 'Down-Cut' spirals.

Amana Tool ® 47090 Carbide Tipped Flush Trim 1/4 Dia x 1/2 x 1/4 Inch Shank

Use this flush trimming bit for laminate work or for template and pattern work. For template application, the bearing follows the template, while the cutting edges trim the workpiece. With the router handheld, the template is on the bottom of the work. With a table-mounted router, the template is on top. A two-flute bit is a good general-purpose choice, providing fast cuts and good finishes. Excellent for template work. 1/4" diameter for closer inside corner cutting only; bearings not guaranteed due to size.

Amana Tool ® 47092 Carbide Tipped Flush Trim 1/4 Dia x 1 Inch x 1/4 Shank

Use this flush trimming bit for laminate work or for template and pattern work. For template application, the bearing follows the template, while the cutting edges trim the workpiece. With the router handheld, the template is on the bottom of the work. With a table-mounted router, the template is on top. A two-flute bit is a good general-purpose choice, providing fast cuts and good finishes. Excellent for template work. 1/4" diameter for closer inside corner cutting only; bearings not guaranteed due to size.

Amana Tool ® 47100 Carbide Tipped Flush Trim 3/8 Dia x 1 Inch x 1/4 Shank

Use this flush trimming bit for laminate work or for template and pattern work. For template application, the bearing follows the template, while the cutting edges trim the workpiece. With the router handheld, the template is on the bottom of the work. With a table-mounted router, the template is on top. A two-flute bit is a good general-purpose choice, providing fast cuts and good finishes. Excellent for template work.

Amana Tool ® 47102 Carbide Tipped Flush Trim 3/8 Dia x 1/2 x 1/4 Inch Shank

Use this flush trimming bit for laminate work or for template and pattern work. For template application, the bearing follows the template, while the cutting edges trim the workpiece. With the router handheld, the template is on the bottom of the work. With a table-mounted router, the template is on top. A two-flute bit is a good general-purpose choice, providing fast cuts and good finishes. Excellent for template work.

Amana Tool ® 47104 Carbide Tipped Flush Trim 1/2 Dia x 1 Inch x 1/4 Shank

Use this flush trimming bit for laminate work or for template and pattern work. For template application, the bearing follows the template, while the cutting edges trim the workpiece. With the router handheld, the template is on the bottom of the work. With a table-mounted router, the template is on top. A two-flute bit is a good general-purpose choice, providing fast cuts and good finishes. Excellent for template work.

Amana Tool ® 47105 Carbide Tipped Dynabit Laminate Flush Trim 1/2 Dia x 1 Inch x 1/4 Shank

The Dynabit™ line features a modest down-shear for an excellent finish. The helix bits have a spiral-like twist to the cutting edges, making them especially good on difficult materials such as melamine. An adhesive-trapping gap between cutting edges and pilot bearing is featured on tools #47111 & #47113.

Amana Tool ® 47106 Carbide Tipped Flush Trim 1/2 Dia x 1/2 x 1/4 Inch Shank

Use this flush trimming bit for laminate work or for template and pattern work. For template application, the bearing follows the template, while the cutting edges trim the workpiece. With the router handheld, the template is on the bottom of the work. With a table-mounted router, the template is on top. A two-flute bit is a good general-purpose choice, providing fast cuts and good finishes. Excellent for template work.

Amana Tool ® 47114 Carbide Tipped Flush Trim 1/2 Dia x 1 Inch x 1/4 Shank 3-Flute

For an extremely smooth finish, choose the three-flute configuration. It is especially good to use on laminates that tend to chip easily.

Amana Tool ® 47116 Carbide Tipped Flush Trim 1/2 Dia x 1/2 x 1/4 Inch Shank 3-Flute

For an extremely smooth finish, choose the three-flute configuration. It is especially good to use on laminates that tend to chip easily.

Amana Tool ® 47118 Carbide Tipped Flush Trim 1/2 Dia x 1 Inch x 1/2 Shank 3-Flute

For an extremely smooth finish, choose the three-flute configuration. It is especially good to use on laminates that tend to chip easily.

Amana Tool ® 47124 Carbide Tipped Flush Trim 1/2 Dia x 1-1/2 x 1/2 Inch Shank

Use this bit for template or pattern work where the workpiece is unusually thick. The two-flute configuration cuts fast and produces a smooth finish. For a superior finish, use the three-flute version. Twin bearings on selected tools provide better contact with reference edge and more stability in the cut.

Amana Tool ® 47126 Carbide Tipped Flush Trim 1/2 Dia x 2 Inch x 1/2 Shank with Double Ball Bearing

Use this bit for template or pattern work where the workpiece is unusually thick. The two-flute configuration cuts fast and produces a smooth finish. For a superior finish, use the three-flute version. Twin bearings on selected tools provide better contact with reference edge and more stability in the cut.

Amana Tool ® 47150 Carbide Tipped No-File Trim .059 Radius x 1/2 Dia x 3/8 x 1/4 Inch Shank

Eliminate the time-consuming hand-filing that normally follows each trimming cut on a laminate job. Our No-File™ bit "breaks" the sharp edge as it trims the laminate flush. When used properly, the resulting edge is smooth and has a slight radius.

Amana Tool ® 47160 Carbide Tipped Flush Trim V Groove 5/8 Dia x 1 Inch x 1/4 Shank

Trim the edges of face frames flush with cabinet sides with this bit. At the same time, cut a decorative 'V' groove to conceal the seam between the frame and the case.

Amana Tool ® 47180 Carbide Tipped Dynabit Laminate Trim, Flush Helix 5/8 Dia x 5/8 x 1/4 Inch Shank

The Dynabit™ line features a modest down-shear for an excellent finish. The helix bits have a spiral-like twist to the cutting edges, making them especially good on difficult materials such as melamine. An adhesive-trapping gap between cutting edges and pilot bearing is featured on tools #47111 & #47113.

Amana Tool ® 47200 Carbide Tipped Bevel Laminate Trim 15 Deg x 5/8 Dia x 1/4 x 1/4 Inch Shank with Ball Bearing

This is a steel-bodied, carbide-tipped bit for bevel trimming laminate with a standard router. The solid construction reduces vibration for the smoothest cut possible with a two-flute bit.

Amana Tool ® 47202 Carbide Tipped Bevel Laminate Trim 25 Deg x 3/4 Dia x 1/4 x 1/4 Inch Shank with Ball Bearing

This is a steel-bodied, carbide-tipped bit for bevel trimming laminate with a standard router. The solid construction reduces vibration for the smoothest cut possible with a two-flute bit.

Amana Tool ® 47204 Carbide Tipped Bevel Laminate Trim 45 Deg x 1-3/32 Dia x 1/4 x 1/4 Inch Shank with Ball Bearing

This is a steel-bodied, carbide-tipped bit for bevel trimming laminate with a standard router. The solid construction reduces vibration for the smoothest cut possible with a two-flute bit.

Amana Tool ® 47300 Carbide Tipped Bevel Laminate Trim 22 Deg x 15/16 Dia x 7/16 x 1/4 Inch Shank with Ball Bearing 3-Flute

The solid construction of this carbide-tipped bit reduces vibration, and its three-flute configuration produces a very smooth cut. Intended for use in a standard router.

Amana Tool ® 47302 Carbide Tipped Bevel Laminate Trim 7 Deg x 3/4 Dia x 7/16 x 1/4 Inch Shank with Ball Bearing 3-Flute

The solid construction of this carbide-tipped bit reduces vibration, and its three-flute configuration produces a very smooth cut. Intended for use in a standard router.

Amana Tool ® 47400 Carbide Tipped 4 Wing Flush Trim Single Bevel Cutter Assembly 7/8 Dia x 1/4 x 1/4 Inch Shank

An assembly offers the option of switching cutters - from flush trim to either of two bevel trims - without removing the bit from the router or even changing the depth-of-cut setup. Four flutes yield a smooth, crisp cut finish.

Amana Tool ® 49104 Carbide Tipped Cove 1/4 Radius x 7/8 Dia x 9/16 x 1/4 Inch Shank

The covetto form – produced by the cove bit – is one of the classic building blocks for many molding profiles. Use it alone or in combination with beads and fillets. Use the cove to detail the edges of casework, doors and drawers, posts and columns. The cove also makes up one-half of the rule joint used on drop-leaf tables, the other half is the corner-round. For best results with a large radius cutter, make a preliminary cut with a smaller radius bit or chamfer the workpiece to reduce the amount of stock to be removed in the finish pass. This will produce a smoother finish and prolong tool life. The largest diameter bits must be run at reduced speed. Use in a handheld or table-mounted router.

Amana Tool ® 49112 Carbide Tipped Cove 3/8 Radius x 1-1/8 Dia x 9/16 x 1/4 Inch Shank

The covetto form – produced by the cove bit – is one of the classic building blocks for many molding profiles. Use it alone or in combination with beads and fillets. Use the cove to detail the edges of casework, doors and drawers, posts and columns. The cove also makes up one-half of the rule joint used on drop-leaf tables, the other half is the corner-round. For best results with a large radius cutter, make a preliminary cut with a smaller radius bit or chamfer the workpiece to reduce the amount of stock to be removed in the finish pass. This will produce a smoother finish and prolong tool life. The largest diameter bits must be run at reduced speed. Use in a handheld or table-mounted router.

Amana Tool ® 49116 Carbide Tipped Cove 1/2 Radius x 1-3/8 Dia x 3/4 x 1/4 Inch Shank

The covetto form – produced by the cove bit – is one of the classic building blocks for many molding profiles. Use it alone or in combination with beads and fillets. Use the cove to detail the edges of casework, doors and drawers, posts and columns. The cove also makes up one-half of the rule joint used on drop-leaf tables, the other half is the corner-round. For best results with a large radius cutter, make a preliminary cut with a smaller radius bit or chamfer the workpiece to reduce the amount of stock to be removed in the finish pass. This will produce a smoother finish and prolong tool life. The largest diameter bits must be run at reduced speed. Use in a handheld or table-mounted router.

Amana Tool ® 49118 Carbide Tipped Cove 1/2 Radius x 1-3/8 Dia x 3/4 x 1/2 Inch Shank

The covetto form – produced by the cove bit – is one of the classic building blocks for many molding profiles. Use it alone or in combination with beads and fillets. Use the cove to detail the edges of casework, doors and drawers, posts and columns. The cove also makes up one-half of the rule joint used on drop-leaf tables, the other half is the corner-round. For best results with a large radius cutter, make a preliminary cut with a smaller radius bit or chamfer the workpiece to reduce the amount of stock to be removed in the finish pass. This will produce a smoother finish and prolong tool life. The largest diameter bits must be run at reduced speed. Use in a handheld or table-mounted router.

Amana Tool ® 49200 Carbide Tipped Roman Ogee 5/32 Radius x 1 Inch Dia x 5/8 x 1/4 Shank

The Roman ogee bit, which has a convex curve coming off the bearing, produces the reverse of the ogee (it isn't an upside-down ogee). The curve starts at the top as a concave, and fairs down into a convex curve. Use in a handheld or table-mounted router.

Amana Tool ® 49204 Carbide Tipped Roman Ogee 1/4 Radius x 1-3/8 Dia x 13/16 x 1/4 Inch Shank

The Roman ogee bit, which has a convex curve coming off the bearing, produces the reverse of the ogee (it isn't an upside-down ogee). The curve starts at the top as a concave, and fairs down into a convex curve. Use in a handheld or table-mounted router.

Amana Tool ® 49300 Rabbeting 3/8 Depth x 1-1/4 Dia x 1/2 x 1/4 Inch Shank

This is the basic rabbeting bit. It cuts 3/8" wide and up to 1/2" deep. Switch to one of four optional ball-bearing guides to alter the width of cut. Use in a handheld or table-mounted router.

Amana Tool ® 49302 Rabbeting 3/8 Depth x 1-1/4 Dia x 1/2 x 1/2 Inch Shank

This is the basic rabbeting bit. It cuts 3/8" wide and up to 1/2" deep. Switch to one of four optional ball-bearing guides to alter the width of cut. Use in a handheld or table-mounted router.

Amana Tool ® 49340 Multi-Rabbet Six Different Rabbet Depths 1-3/8 Dia x 1/2 x 1/4 Inch Shank

The Multi-Rabbet bit steps in 1/16" increments from a 1/8" cut width to 1/2", simply by switching ball-bearing guides. Six different bearings are provided. Depth of cut capacity of 1/2". Use in a handheld or table-mounted router.

Amana Tool ® 49350 Multi-Rabbet Six Different Rabbet Depths 1-3/8 Dia x 1/2 x 1/2 Inch Shank

The Multi-Rabbet bit steps in 1/16" increments from a 1/8" cut width to 1/2", simply by switching ball-bearing guides. Six different bearings are provided. Depth of cut capacity of 1/2". Use in a handheld or table-mounted router.

Amana Tool ® 49402 Carbide Tipped Chamfer 45 Degree x 1-1/4 Dia x 1/2 x 1/2 Inch Shank

Chamfer or bevel edges for decorative effect or to form edge miter joints. Produce crisp, uniform edges at accurate angles. For best results use in a router table.

Amana Tool ® 49408 Carbide Tipped Chamfer 15 Degree x 7/8 Dia x 3/4 x 1/4 Inch Shank

Chamfer or bevel edges for decorative effect or to form edge miter joints. Produce crisp, uniform edges at accurate angles. For best results use in a router table.

Amana Tool ® 49492 Carbide Tipped Corner Round 1/16 Radius x 5/8 Dia x 5/16 x 1/4 Inch Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit.

Amana Tool ® 49496 Carbide Tipped Corner Round 1/8 Radius x 3/4 Dia x 3/8 x 1/4 Inch Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit.

Amana Tool ® 49500 Carbide Tipped Corner Round 3/16 Radius x 7/8 Dia x 1/2 x 1/4 Inch Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit.

Amana Tool ® 49504 Carbide Tipped Corner Round 1/4 Radius x 1 Inch Dia x 1/2 x 1/4 Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit.

Amana Tool ® 49506 Carbide Tipped Corner Round 1/4 Radius x 1 Inch Dia x 1/2 x 1/2 Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit.

Amana Tool ® 49512 Carbide Tipped Corner Round 3/8 Radius x 1-1/4 Dia x 5/8 x 1/4 Inch Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit.

Amana Tool ® 49514 Carbide Tipped Corner Round 3/8 Radius x 1-1/4 Dia x 5/8 x 1/2 Inch Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit.

Amana Tool ® 49516 Carbide Tipped Corner Round 1/2 Radius x 1-1/2 Dia x 3/4 x 1/4 Inch Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit.

Amana Tool ® 49519 Carbide Tipped Corner Round 5/8 Radius x 1-3/4 Dia x 7/8 x 1/2 Inch Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit. Maximum RPM 28,000.

Amana Tool ® 49520 Carbide Tipped Corner Round 3/4 Radius x 2 Inch Dia x 1 Inch x 1/2 Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit. Maximum RPM 22,000

Amana Tool ® 51200 Solid Carbide Panel Pilot Flush Trim 1/4 Dia x 1/4 x 1/4 Inch Shank 1-Flute

The ideal laminate trimming bit for high-volume production. Solid carbide and integral pilot (no bearing to maintain) extend life of bit, slim configuration reduces vibration. Suitable for routers and trimmers.

Amana Tool ® 51202 Solid Carbide Panel Pilot Bevel Trim 7 Degree x 1/4 Dia x 1/4 x 1/4 Inch Shank 1-Flute

The ideal laminate trimming bit for high-volume production. Solid carbide and integral pilot (no bearing to maintain) extend life of bit, slim configuration reduces vibration. Suitable for routers and trimmers.

Amana Tool ® 51432 Solid Carbide InVectra Aluminum Laminate Trim 1/4 Dia x 5/8 x 1/2 Inch Shank

With Invectra™ router bits, kitchen fabricators, remodelers and construction workers can perform any kind of cut and trim job in aluminum laminates. Designed and tested for trimming all decorative aluminum laminates. Engineered from an Amana Tool® exclusive carbide grade designed specifically for cutting both aluminum laminates and wood-based substrate materials. Each bit is fitted with a steel bearing guide that enables users to trim laminate materials flush to the substrate, allowing you to perform any metal trim job to perfection!

Amana Tool ® 51558 Carbide Tipped Bullnose 17/64 Radius x 1-1/32 Dia x 1 Inch x 1/2 Shank

Shape the full edge of a workpiece with a bullnose radius bit. Ideal for shaping stair treads, window sills, table and counter edges, shelves, and making moldings. The "nose diameter" (M) is the thickness of stock that can be nosed, i.e., given a full 180-degree roundover. Flats at top and bottom of the cutting edges create fillets on stock thicker than the nose diameter. Must be used with an edge guide on handheld routers or the fence on a router table.

Amana Tool ® 51560 Carbide Tipped Bullnose 3/8 Radius x 1-1/4 Dia x 1-5/16 x 1/2 Inch Shank

Shape the full edge of a workpiece with a bullnose radius bit. Ideal for shaping stair treads, window sills, table and counter edges, shelves, and making moldings. The "nose diameter" (M) is the thickness of stock that can be nosed, i.e., given a full 180-degree roundover. Flats at top and bottom of the cutting edges create fillets on stock thicker than the nose diameter. Must be used with an edge guide on handheld routers or the fence on a router table. Maximum RPM 20,000.

Amana Tool ® 53400 Slotting Cutter Assembly 3 Wing x 1-7/8 Dia x 1/16 x 1/4 Inch Shank

Groove edges for T-moldings, splines or biscuits, and other purposes. Rout tongue-and-groove joinery. Slotting cutters are available with either 2-wing or 3-wing cutters. Each assembly includes a cutter, bearing for a 1/2" deep cut, and either a 1/4"-, 3/8"-, or 1/2"-shank arbor. Use in a handheld or table-mounted router. All assemblies include cutter, arbor and ball bearing.

Amana Tool ® 53406 Slotting Cutter Assembly 3 Wing x 1-7/8 Dia x 1/8 x 1/4 Inch Shank

Groove edges for T-moldings, splines or biscuits, and other purposes. Rout tongue-and-groove joinery. Slotting cutters are available with either 2-wing or 3-wing cutters. Each assembly includes a cutter, bearing for a 1/2" deep cut, and either a 1/4"-, 3/8"-, or 1/2"-shank arbor. Use in a handheld or table-mounted router. All assemblies include cutter, arbor and ball bearing.

Amana Tool ® 53410 Slotting Cutter Assembly 3 Wing x 1-7/8 Dia x 1/4 x 1/4 Inch Shank

Groove edges for T-moldings, splines or biscuits, and other purposes. Rout tongue-and-groove joinery. Slotting cutters are available with either 2-wing or 3-wing cutters. Each assembly includes a cutter, bearing for a 1/2" deep cut, and either a 1/4"-, 3/8"-, or 1/2"-shank arbor. Use in a handheld or table-mounted router. All assemblies include cutter, arbor and ball bearing.

Amana Tool ® 54102 Carbide Tipped Classical Bead & Cove 13/64 x 5/16 Radius x 1-1/4 Dia x 1/2 x 1/4 Inch Shank

This bead and cove combines the two basic forms, separating them with a fillet. The cove comes off the pilot bearing. Produce a complex profile in a single pass. Use in a handheld or table-mounted router.

Amana Tool ® 54160 Carbide Tipped Corner Round 1/8 Radius x 7/8 Dia x 9/16 x 1/4 Inch Shank

Produce three slightly different profiles using this bit - an edge bead with or without a fillet and a full corner bead - by altering the bit extension or rolling the work piece between passes. This group of hard-to-find tools is particularly suitable for antique reproductions and restoration projects. Use in a handheld or table-mounted router.

Amana Tool ® 55400 Carbide Tipped Tongue & Groove 3/8 Kerf x 1-5/8 Dia x 3/4 x 1/2 Inch Shank Assembly for 1/2 to 3/4 Material

Cut perfectly fitted tongue-and-groove joints on stock between 1/2" and 3/4" thick with a table-mounted router and this assembly. The tool consists of an arbor with an integral shank, two identical, removable slotting cutters, and a pair of bearings. To cut tongues, sandwich one bearing between the two cutters (as in drawing A). To cut slots, mount one cutter between the two bearings (as in drawing B). Can be used on 1/2" through 3/4" thick material.