Cincinnati
(800) 736-3524
Columbus
(800) 784-1475
Lexington
(800) 844-2768
Louisville
(844) 287-3883

Boring Bits

View as Grid List
Sort by

Amana Tool ® 201005 Carbide Tipped Brad Point Boring Bit R/H 5mm Dia x 57mm Long x 10mm Shank

Amana Tool® dowel drills are coated with a special Polytetrafluoroethylene (PTFE), a non-stick color coating. In cases where the carbide tip cutting edges are coated, there is no need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570° F. The coating reduces the friction between the chip and the body inside the flute and it helps to clear the chips out of the hole during the drilling creating a cooler drilling area, no burning and longer lasting cutting edge.

Amana Tool ® 201008 Carbide Tipped Brad Point Boring Bit R/H 8mm Dia x 57mm Long x 10mm Shank

Amana Tool® dowel drills are coated with a special Polytetrafluoroethylene (PTFE), a non-stick color coating. In cases where the carbide tip cutting edges are coated, there is no need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570° F. The coating reduces the friction between the chip and the body inside the flute and it helps to clear the chips out of the hole during the drilling creating a cooler drilling area, no burning and longer lasting cutting edge.

Amana Tool ® 203261 Carbide Tipped Hinge Boring Bit R/H 26mm Dia x 57mm Long x 10mm Shank

Application: Boring machines (10mm shank) and drill presses (3/8" shank).

Amana Tool ® 203351 Carbide Tipped Hinge Boring Bit R/H 35mm Dia x 57mm Long x 10mm Shank

Application: Boring machines (10mm shank) and drill presses (3/8" shank).

Amana Tool ® 203401 Carbide Tipped Hinge Boring Bit R/H 40mm Dia x 57mm Long x 10mm Shank

Application: Boring machines (10mm shank) and drill presses (3/8" shank).

Amana Tool ® 204005 Carbide Tipped Brad Point Boring Bit R/H 5mm Dia x 70mm Long x 10mm Shank

Amana Tool® dowel drills are coated with a special Polytetrafluoroethylene (PTFE), a non-stick color coating. In cases where the carbide tip cutting edges are coated, there is no need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570° F. The coating reduces the friction between the chip and the body inside the flute and it helps to clear the chips out of the hole during the drilling creating a cooler drilling area, no burning and longer lasting cutting edge.

Amana Tool ® 301005 Carbide Tipped Brad Point Boring Bit L/H 5mm Dia x 57mm Long x 10mm Shank

Amana Tool® dowel drills are coated with a special Polytetrafluoroethylene (PTFE), a non-stick color coating. In cases where the carbide tip cutting edges are coated, there is no need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570° F. The coating reduces the friction between the chip and the body inside the flute and it helps to clear the chips out of the hole during the drilling creating a cooler drilling area, no burning and longer lasting cutting edge.

Amana Tool ® 301008 Carbide Tipped Brad Point Boring Bit L/H 8mm Dia x 57mm Long x 10mm Shank

Amana Tool® dowel drills are coated with a special Polytetrafluoroethylene (PTFE), a non-stick color coating. In cases where the carbide tip cutting edges are coated, there is no need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570° F. The coating reduces the friction between the chip and the body inside the flute and it helps to clear the chips out of the hole during the drilling creating a cooler drilling area, no burning and longer lasting cutting edge.

Amana Tool ® 301010 Carbide Tipped Brad Point Boring Bit L/H 10mm Dia x 57mm Long x 10mm Shank

Amana Tool® dowel drills are coated with a special Polytetrafluoroethylene (PTFE), a non-stick color coating. In cases where the carbide tip cutting edges are coated, there is no need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570° F. The coating reduces the friction between the chip and the body inside the flute and it helps to clear the chips out of the hole during the drilling creating a cooler drilling area, no burning and longer lasting cutting edge.

Amana Tool ® 304005 Carbide Tipped Brad Point Boring Bit L/H 5mm Dia x 70mm Long x 10mm Shank

Amana Tool® dowel drills are coated with a special Polytetrafluoroethylene (PTFE), a non-stick color coating. In cases where the carbide tip cutting edges are coated, there is no need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570° F. The coating reduces the friction between the chip and the body inside the flute and it helps to clear the chips out of the hole during the drilling creating a cooler drilling area, no burning and longer lasting cutting edge.

Amana Tool ® 45190 Straight Plunge High Production 1/16 Dia x 3/16 x 1/4 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced. 45190 features a solid carbide cutting edge.

Amana Tool ® 45200 Straight Plunge High Production 1/8 Dia x 7/16 x 1/4 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced. 45200 features a solid carbide cutting edge.

Amana Tool ® 45202 Straight Plunge High Production 3/16 Dia x 7/16 x 1/4 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced. 45202 features a solid carbide cutting edge.

Amana Tool ® 45208 Carbide Tipped Straight Plunge High Production 1/4 Dia x 3/4 x 1/4 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45210 Carbide Tipped Straight Plunge High Production 1/4 Dia x 1 Inch x 1/4 Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45211 Carbide Tipped Straight Plunge High Production 1/4 Dia x 1 Inch x 1/4 Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45218 Carbide Tipped Straight Plunge High Production 3/8 Dia x 1 Inch x 1/4 Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45226 Carbide Tipped Straight Plunge High Production 1/2 Dia x 1 Inch x 1/4 Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45228 Carbide Tipped Straight Plunge High Production 5/8 Dia x 3/4 x 1/4 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45230 Carbide Tipped Straight Plunge High Production 3/4 Dia x 3/4 x 1/4 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45414 Carbide Tipped Straight Plunge High Production 3/8 Dia x 1 Inch x 1/2 Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45418 Carbide Tipped Straight Plunge 1/2 Dia x 1 Inch x 1/2 Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45420 Carbide Tipped Straight Plunge 1/2 Dia x 1-1/4 x 1/2 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45422 Carbide Tipped Straight Plunge 1/2 Dia x 1-1/2 x 1/2 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45426 Carbide Tipped Straight Plunge 1/2 Dia x 2 Inch x 1/2 Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45427 Carbide Tipped Straight Plunge 1/2 Dia x 2-1/2 x 1/2 Inch Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45445 Carbide Tipped Undersized Plywood Dado Plunge 23/32 Dia x 1-1/4 x 1/2 Inch Shank for Plywood Thickness 3/4 minus 1/32

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45448 Carbide Tipped Straight Plunge High Production 1 Inch Dia x 1-1/4 x 1/2 Shank

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

Amana Tool ® 45500 Carbide Tipped Mortising 1/2 Dia x 3/4 x 1/4 Inch Shank

Cutting mortises for hinges and locks can be challenging; the mortise depth must be accurate for smooth operation and the edges must be sharp for a clean, professional installation. These mortise bits make hardware installation a snap. The large gullet between the two flutes clears chips away quickly and the cutter geometry creates a crisp outline for a perfect fit.

Amana Tool ® 45502 Carbide Tipped Mortising 5/8 Dia x 3/4 x 1/4 Inch Shank

Cutting mortises for hinges and locks can be challenging; the mortise depth must be accurate for smooth operation and the edges must be sharp for a clean, professional installation. These mortise bits make hardware installation a snap. The large gullet between the two flutes clears chips away quickly and the cutter geometry creates a crisp outline for a perfect fit.

Amana Tool ® 45700 Carbide Tipped V Groove 90 Deg x 3/8 Dia x 7/16 x 1/4 Inch Shank

Cut decorative "V" grooves and lettering on signs with this 'V' Groove bit. Use with an edge guide to chamfer and bevel edges. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45704 Carbide Tipped V Groove 90 Deg x 1/2 Dia x 1/2 x 1/4 Inch Shank

Cut decorative "V" grooves and lettering on signs with this "V" Groove bit. Use with an edge guide to chamfer and bevel edges. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45705 Carbide Tipped V Groove 60 Deg x 1/2 Dia x 5/8 x 1/4 Inch Shank

Cut decorative "V" grooves and lettering on signs with this "V" Groove bits. Use with an edge guide to chamfer and bevel edges. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45730 Carbide Tipped V Groove Signmaking & Lettering 60 Deg x 9/16 Dia x 7/16 x 1/4 Inch Shank

Originally developed in Europe specifically for professional signmakers, this solid-carbide bit features an extra-fine 60° point that produces a clean, precise cut. For those intricate lines, this bit is superior to standard "V" groover. Makes crisp, clean cuts in solid woods, MDF and acrylics.

Amana Tool ® 45750 Carbide Tipped V Groove 90 Deg x 1/2 Dia x 1/2 x 1/4 Inch Shank with Upper BB

Designed for fluting and 'V' grooving cuts guided by a template or pattern. The shank-mounted ball-bearing pilot rides along the template edge, and the cutter duplicates the template contour in the work piece. With a handheld router, the template must be on top of the work piece. With a table-mounted router, the template must be on bottom of the work piece. 90° ‘V’ Groove bit is for decorative purposes and is not intended for ‘miter-folding’, etc.

Amana Tool ® 45804 Carbide Tipped Dovetail 14 Deg x 1/2 Dia x 1/2 x 1/4 Inch Shank

The 14° dovetail bit is used with common half-blind dovetail jigs, as well as with Omnijig®, Incra® and Leigh® jigs.

Amana Tool ® 45806 Carbide Tipped Dovetail 14 Deg x .532 Dia x 1/2 x 1/2 Inch Shank for Omnijig & Incra

The 14° dovetail bit is used with common half-blind dovetail jigs, as well as with Omnijig®, Incra® and Leigh® jigs.

Amana Tool ® 45904 Carbide Tipped Core Box 1/8 Radius x 1/4 Dia x 1/4 x 1/4 Inch Shank

Cut half-round grooves for fluted moldings, columns, millwork and signs using a core box bit. Used with an edge guide, it can cut coves. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45906 Carbide Tipped Core Box 3/16 Radius x 3/8 Dia x 1/4 x 1/4 Inch Shank

Cut half-round grooves for fluted moldings, columns, millwork and signs using a core box bit. Used with an edge guide, it can cut coves. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45910 Carbide Tipped Core Box 1/4 Radius x 1/2 Dia x 3/8 x 1/4 Inch Shank

Cut half-round grooves for fluted moldings, columns, millwork and signs using a core box bit. Used with an edge guide, it can cut coves. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45918 Carbide Tipped Core Box 3/8 Radius x 3/4 Dia x 7/16 x 1/4 Inch Shank

Cut half-round grooves for fluted moldings, columns, millwork and signs using a core box bit. Used with an edge guide, it can cut coves. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45920 Carbide Tipped Core Box 3/8 Radius x 3/4 Dia x 7/16 x 1/2 Inch Shank

Cut half-round grooves for fluted moldings, columns, millwork and signs using a core box bit. Used with an edge guide, it can cut coves. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45924 Carbide Tipped Core Box 1/2 Radius x 1 Inch Dia x 5/8 x 1/4 Shank

Cut half-round grooves for fluted moldings, columns, millwork and signs using a core box bit. Used with an edge guide, it can cut coves. Can be used with handheld, table-mounted and CNC routers.

Amana Tool ® 45950 Carbide Tipped Core Box 1/4 Radius x 1/2 Dia x 3/8 x 1/4 Inch Shank with Upper BB

Designed for fluting and 'V' grooving cuts guided by a template or pattern. The shank-mounted ball-bearing pilot rides along the template edge, and the cutter duplicates the template contour in the work piece. With a handheld router, the template must be on top of the work piece. With a table-mounted router, the template must be on bottom of the work piece.

Amana Tool ® 46102 Solid Carbide Spiral Plunge 1/4 Dia x 3/4 x 1/4 Inch Shank Up-Cut

Spiral-flute bits combine a shearing action in cutting with an augering action in chip clearance. The shearing action yields an especially clean, accurate cut, while the augering action clears chips from the cut. The ‘Up-Cut’ shears from the bottom up, pulling chips from the bottom up, thus allowing deeper penetration with less stress on the tool. An excellent choice for mortising. Special unique carbide grade, increased clearance geometry and razor-sharp cutting edges with polished flutes, provide a superior finish and longer tool life, especially in abrasive materials. Great for production settings and excellent for creating grooves and dado cuts in particleboard, plywood and laminate. Primarily used on CNC machines and other automatic routers. Can be used with handheld and table-mounted portable routers.

Amana Tool ® 46106 Solid Carbide Spiral Plunge 1/2 Dia x 1-1/4 x 1/2 Inch Shank Up-Cut

Spiral-flute bits combine a shearing action in cutting with an augering action in chip clearance. The shearing action yields an especially clean, accurate cut, while the augering action clears chips from the cut. The ‘Up-Cut’ shears from the bottom up, pulling chips from the bottom up, thus allowing deeper penetration with less stress on the tool. An excellent choice for mortising. Special unique carbide grade, increased clearance geometry and razor-sharp cutting edges with polished flutes, provide a superior finish and longer tool life, especially in abrasive materials. Great for production settings and excellent for creating grooves and dado cuts in particleboard, plywood and laminate. Primarily used on CNC machines and other automatic routers. Can be used with handheld and table-mounted portable routers.

Amana Tool ® 46188 CNC Solid Carbide Compression Spiral 1/2 Dia x 1-1/4 x 1/2 Inch Shank

Special unique carbide for longer lifetime in abrasive material. Designed for CNC applications requiring high feed rates and a clean finish. Particularly suitable for double-sided melamine or laminated material.

Amana Tool ® 46190 CNC Solid Carbide Compression Spiral 1/2 Dia x 1-5/8 x 1/2 Inch Shank

Special unique carbide for longer lifetime in abrasive material. Designed for CNC applications requiring high feed rates and a clean finish. Particularly suitable for double-sided melamine or laminated material.

Amana Tool ® 46202 Solid Carbide Spiral Plunge 1/4 Dia x 3/4 x 1/4 Inch Shank

Spiral-flute bits combine a shearing action in cutting with an augering action in chip clearance. The shearing action yields an especially clean, accurate cut, while the augering action clears chips from the cut. The ‘Down-Cut’ cuts from the surface down, leaving a smooth edge at the surface. Special unique carbide grade, increased clearance geometry and razor-sharp cutting edges with polished flutes, provide a superior finish and longer tool life, especially in abrasive materials. Great for production settings and excellent for creating grooves and dado cuts in particleboard, plywood and laminate. Primarily used on CNC machines and other automatic routers. Can be used with handheld and table-mounted portable routers.

Amana Tool ® 46206 Solid Carbide Spiral Plunge 1/2 Dia x 1-1/4 x 1/2 Inch Shank Down-Cut

Spiral-flute bits combine a shearing action in cutting with an augering action in chip clearance. The shearing action yields an especially clean, accurate cut, while the augering action clears chips from the cut. The ‘Down-Cut’ cuts from the surface down, leaving a smooth edge at the surface. Special unique carbide grade, increased clearance geometry and razor-sharp cutting edges with polished flutes, provide a superior finish and longer tool life, especially in abrasive materials. Great for production settings and excellent for creating grooves and dado cuts in particleboard, plywood and laminate. Primarily used on CNC machines and other automatic routers. Can be used with handheld and table-mounted portable routers.

Amana Tool ® 49104 Carbide Tipped Cove 1/4 Radius x 7/8 Dia x 9/16 x 1/4 Inch Shank

The covetto form – produced by the cove bit – is one of the classic building blocks for many molding profiles. Use it alone or in combination with beads and fillets. Use the cove to detail the edges of casework, doors and drawers, posts and columns. The cove also makes up one-half of the rule joint used on drop-leaf tables, the other half is the corner-round. For best results with a large radius cutter, make a preliminary cut with a smaller radius bit or chamfer the workpiece to reduce the amount of stock to be removed in the finish pass. This will produce a smoother finish and prolong tool life. The largest diameter bits must be run at reduced speed. Use in a handheld or table-mounted router.

Amana Tool ® 49112 Carbide Tipped Cove 3/8 Radius x 1-1/8 Dia x 9/16 x 1/4 Inch Shank

The covetto form – produced by the cove bit – is one of the classic building blocks for many molding profiles. Use it alone or in combination with beads and fillets. Use the cove to detail the edges of casework, doors and drawers, posts and columns. The cove also makes up one-half of the rule joint used on drop-leaf tables, the other half is the corner-round. For best results with a large radius cutter, make a preliminary cut with a smaller radius bit or chamfer the workpiece to reduce the amount of stock to be removed in the finish pass. This will produce a smoother finish and prolong tool life. The largest diameter bits must be run at reduced speed. Use in a handheld or table-mounted router.

Amana Tool ® 49116 Carbide Tipped Cove 1/2 Radius x 1-3/8 Dia x 3/4 x 1/4 Inch Shank

The covetto form – produced by the cove bit – is one of the classic building blocks for many molding profiles. Use it alone or in combination with beads and fillets. Use the cove to detail the edges of casework, doors and drawers, posts and columns. The cove also makes up one-half of the rule joint used on drop-leaf tables, the other half is the corner-round. For best results with a large radius cutter, make a preliminary cut with a smaller radius bit or chamfer the workpiece to reduce the amount of stock to be removed in the finish pass. This will produce a smoother finish and prolong tool life. The largest diameter bits must be run at reduced speed. Use in a handheld or table-mounted router.

Amana Tool ® 49118 Carbide Tipped Cove 1/2 Radius x 1-3/8 Dia x 3/4 x 1/2 Inch Shank

The covetto form – produced by the cove bit – is one of the classic building blocks for many molding profiles. Use it alone or in combination with beads and fillets. Use the cove to detail the edges of casework, doors and drawers, posts and columns. The cove also makes up one-half of the rule joint used on drop-leaf tables, the other half is the corner-round. For best results with a large radius cutter, make a preliminary cut with a smaller radius bit or chamfer the workpiece to reduce the amount of stock to be removed in the finish pass. This will produce a smoother finish and prolong tool life. The largest diameter bits must be run at reduced speed. Use in a handheld or table-mounted router.

Amana Tool ® 49200 Carbide Tipped Roman Ogee 5/32 Radius x 1 Inch Dia x 5/8 x 1/4 Shank

The Roman ogee bit, which has a convex curve coming off the bearing, produces the reverse of the ogee (it isn't an upside-down ogee). The curve starts at the top as a concave, and fairs down into a convex curve. Use in a handheld or table-mounted router.

Amana Tool ® 49204 Carbide Tipped Roman Ogee 1/4 Radius x 1-3/8 Dia x 13/16 x 1/4 Inch Shank

The Roman ogee bit, which has a convex curve coming off the bearing, produces the reverse of the ogee (it isn't an upside-down ogee). The curve starts at the top as a concave, and fairs down into a convex curve. Use in a handheld or table-mounted router.

Amana Tool ® 49300 Rabbeting 3/8 Depth x 1-1/4 Dia x 1/2 x 1/4 Inch Shank

This is the basic rabbeting bit. It cuts 3/8" wide and up to 1/2" deep. Switch to one of four optional ball-bearing guides to alter the width of cut. Use in a handheld or table-mounted router.

Amana Tool ® 49302 Rabbeting 3/8 Depth x 1-1/4 Dia x 1/2 x 1/2 Inch Shank

This is the basic rabbeting bit. It cuts 3/8" wide and up to 1/2" deep. Switch to one of four optional ball-bearing guides to alter the width of cut. Use in a handheld or table-mounted router.

Amana Tool ® 49340 Multi-Rabbet Six Different Rabbet Depths 1-3/8 Dia x 1/2 x 1/4 Inch Shank

The Multi-Rabbet bit steps in 1/16" increments from a 1/8" cut width to 1/2", simply by switching ball-bearing guides. Six different bearings are provided. Depth of cut capacity of 1/2". Use in a handheld or table-mounted router.

Amana Tool ® 49350 Multi-Rabbet Six Different Rabbet Depths 1-3/8 Dia x 1/2 x 1/2 Inch Shank

The Multi-Rabbet bit steps in 1/16" increments from a 1/8" cut width to 1/2", simply by switching ball-bearing guides. Six different bearings are provided. Depth of cut capacity of 1/2". Use in a handheld or table-mounted router.

Amana Tool ® 49360 Carbide Tipped Superabbet 2 Dia x 7/8 x 1/2 Inch Shank

This ingenious tool features both interchangeable cutting edges and an interchangeable guide collar, enabling you to cut a wide range of rabbets. Changing the collars on the twin ball-bearing guide steps the cut width in 1/16" increments from flush through 3/4" with five extra "plywood" sizes. Between the standard and optional collars, there are 18 different rabbet sizes available. The deep guide collar design adds stability to the tool for hand-held router operations. The basic 2"-diameter bit includes a hex key, instructions, and all necessary parts for 5/8" and 3/4" width rabbets. The "RC" version has extra-long double-edged carbide inserts which enables the bit to cut 30mm high. Inserts can be rotated or replaced without removing the bit from the router.

Amana Tool ® 49402 Carbide Tipped Chamfer 45 Degree x 1-1/4 Dia x 1/2 x 1/2 Inch Shank

Chamfer or bevel edges for decorative effect or to form edge miter joints. Produce crisp, uniform edges at accurate angles. For best results use in a router table.

Amana Tool ® 49404 Carbide Tipped Chamfer 45 Degree x 1-31/32 Inch Dia x 3/4 x 1/2 Shank

Chamfer or bevel edges for decorative effect or to form edge miter joints. Produce crisp, uniform edges at accurate angles. For best results use in a router table. Will completely chamfer 3/4" material.

Amana Tool ® 49406 Carbide Tipped Chamfer 45 Degree x 2-3/8 Dia x 1 Inch x 1/2 Shank

Chamfer or bevel edges for decorative effect or to form edge miter joints. Produce crisp, uniform edges at accurate angles. For best results use in a router table. Will completely chamfer 1" material.

Amana Tool ® 49408 Carbide Tipped Chamfer 15 Degree x 7/8 Dia x 3/4 x 1/4 Inch Shank

Chamfer or bevel edges for decorative effect or to form edge miter joints. Produce crisp, uniform edges at accurate angles. For best results use in a router table.

Amana Tool ® 49492 Carbide Tipped Corner Round 1/16 Radius x 5/8 Dia x 5/16 x 1/4 Inch Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit.

Amana Tool ® 49496 Carbide Tipped Corner Round 1/8 Radius x 3/4 Dia x 3/8 x 1/4 Inch Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit.

Amana Tool ® 49500 Carbide Tipped Corner Round 3/16 Radius x 7/8 Dia x 1/2 x 1/4 Inch Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit.

Amana Tool ® 49504 Carbide Tipped Corner Round 1/4 Radius x 1 Inch Dia x 1/2 x 1/4 Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit.

Amana Tool ® 49506 Carbide Tipped Corner Round 1/4 Radius x 1 Inch Dia x 1/2 x 1/2 Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit.

Amana Tool ® 49512 Carbide Tipped Corner Round 3/8 Radius x 1-1/4 Dia x 5/8 x 1/4 Inch Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit.

Amana Tool ® 49514 Carbide Tipped Corner Round 3/8 Radius x 1-1/4 Dia x 5/8 x 1/2 Inch Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit.

Amana Tool ® 49516 Carbide Tipped Corner Round 1/2 Radius x 1-1/2 Dia x 3/4 x 1/4 Inch Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit.

Amana Tool ® 49519 Carbide Tipped Corner Round 5/8 Radius x 1-3/4 Dia x 7/8 x 1/2 Inch Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit. Maximum RPM 28,000.

Amana Tool ® 49520 Carbide Tipped Corner Round 3/4 Radius x 2 Inch Dia x 1 Inch x 1/2 Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit. Maximum RPM 22,000

Amana Tool ® 49522 Carbide Tipped Corner Round 1 Radius x 2-1/2 Dia x 1-1/4 x 1/2 Inch Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit. Maximum RPM 18,000. Use in a table-mounted router. Not for use in a handheld router! Not guaranteed due to extreme diameter and radius. For best results it is recommended to use a smaller radius bit or chamfer the material prior to using these large radius tools. Tool life will be prolonged and a smoother finish will result.

Amana Tool ® 49526 Carbide Tipped Corner Round 1-1/2 Radius x 3-1/2 Dia x 1-3/4 x 1/2 Inch Shank

The basic edge-forming bit, the corner-rounding bit rounds an edge to a given radius. The tool is shouldered to cut a fillet. The cut can be used to ease edges, as a simple profile, or as a part of a complex one. Also known as roundover, rounding over and quarter-round. If a smaller pilot bearing is used, a second shoulder can be produced, in effect making the bit a beading bit. Maximum RPM 15,000. Use in a table-mounted router. Not for use in a handheld router! Not guaranteed due to extreme diameter and radius. For best results it is recommended to use a smaller radius bit or chamfer the material prior to using these large radius tools. Tool life will be prolonged and a smoother finish will result.

Amana Tool ® 51402 Solid Carbide CNC Spiral 'O' Flute, Aluminum Cutting 1/4 Dia x 5/8 x 1/4 Inch Shank Up-Cut

To be used only on CNC machines and routers with automatic feeding. Using the highest quality sub-micrograin carbide, these bits have a special proprietary edge processing system featuring a super high polished cutting edge with a unique “mirror finish”, resulting in clean cuts, less chance for chip re-welding, a superior surface finish and a longer tool life. Right hand helix, right hand cut.

Amana Tool ® 51404 Solid Carbide CNC Spiral 'O' Flute, Plastic Cutting 1/4 Dia x 3/4 x 1/4 Inch Shank Up-Cut Router Bit

To be used only on CNC machines and routers with automatic feeding. Produce super clean, smooth cuts, especially in acrylic materials (Plexiglas®, Lucite®), other plastics and wood. Bits are made according to strict tolerances from an exclusive carbide grade and polished to a mirror finish using Amana’s unique process. Designed to eject chips up. Ideal for industrial applications and CNC machines. Right hand helix, right hand cut.

Amana Tool ® 51558 Carbide Tipped Bullnose 17/64 Radius x 1-1/32 Dia x 1 Inch x 1/2 Shank

Shape the full edge of a workpiece with a bullnose radius bit. Ideal for shaping stair treads, window sills, table and counter edges, shelves, and making moldings. The "nose diameter" (M) is the thickness of stock that can be nosed, i.e., given a full 180-degree roundover. Flats at top and bottom of the cutting edges create fillets on stock thicker than the nose diameter. Must be used with an edge guide on handheld routers or the fence on a router table.

Amana Tool ® 51560 Carbide Tipped Bullnose 3/8 Radius x 1-1/4 Dia x 1-5/16 x 1/2 Inch Shank

Shape the full edge of a workpiece with a bullnose radius bit. Ideal for shaping stair treads, window sills, table and counter edges, shelves, and making moldings. The "nose diameter" (M) is the thickness of stock that can be nosed, i.e., given a full 180-degree roundover. Flats at top and bottom of the cutting edges create fillets on stock thicker than the nose diameter. Must be used with an edge guide on handheld routers or the fence on a router table. Maximum RPM 20,000.

Amana Tool ® 53400 Slotting Cutter Assembly 3 Wing x 1-7/8 Dia x 1/16 x 1/4 Inch Shank

Groove edges for T-moldings, splines or biscuits, and other purposes. Rout tongue-and-groove joinery. Slotting cutters are available with either 2-wing or 3-wing cutters. Each assembly includes a cutter, bearing for a 1/2" deep cut, and either a 1/4"-, 3/8"-, or 1/2"-shank arbor. Use in a handheld or table-mounted router. All assemblies include cutter, arbor and ball bearing.

Amana Tool ® 53406 Slotting Cutter Assembly 3 Wing x 1-7/8 Dia x 1/8 x 1/4 Inch Shank

Groove edges for T-moldings, splines or biscuits, and other purposes. Rout tongue-and-groove joinery. Slotting cutters are available with either 2-wing or 3-wing cutters. Each assembly includes a cutter, bearing for a 1/2" deep cut, and either a 1/4"-, 3/8"-, or 1/2"-shank arbor. Use in a handheld or table-mounted router. All assemblies include cutter, arbor and ball bearing.

Amana Tool ® 53410 Slotting Cutter Assembly 3 Wing x 1-7/8 Dia x 1/4 x 1/4 Inch Shank

Groove edges for T-moldings, splines or biscuits, and other purposes. Rout tongue-and-groove joinery. Slotting cutters are available with either 2-wing or 3-wing cutters. Each assembly includes a cutter, bearing for a 1/2" deep cut, and either a 1/4"-, 3/8"-, or 1/2"-shank arbor. Use in a handheld or table-mounted router. All assemblies include cutter, arbor and ball bearing.

Amana Tool ® 54102 Carbide Tipped Classical Bead & Cove 13/64 x 5/16 Radius x 1-1/4 Dia x 1/2 x 1/4 Inch Shank

This bead and cove combines the two basic forms, separating them with a fillet. The cove comes off the pilot bearing. Produce a complex profile in a single pass. Use in a handheld or table-mounted router.

Amana Tool ® 54117 Carbide Tipped Traditional Raised Panel 15 Deg x 1-7/16 Angle x 3-3/8 Dia x 1/2 x 1/2 Inch Shank

Create raised panels for cabinet doors, frame-and-panel furniture, and architectural paneling with a raised-panel bit. The cutter forms a fillet to delineate the raised field, a shaped band around the field, and an integral tongue to fit the panel groove in the frame members. The profile contour and the reveal width varies. All tools have 1/2" shanks. Must be used in a table-mounted 3+ horsepower router and run at reduced speed. Use these bits for panels with curved edges. Multiple passes recommended. Maximum RPM 14,000.

Amana Tool ® 54118 Carbide Tipped Ogee Raised Panel 3/4 Radius x 2-5/8 Dia x 5/8 x 1/2 Inch Shank

Create raised panels for cabinet doors, frame-and-panel furniture, and architectural paneling with a raised-panel bit. The cutter forms a fillet to delineate the raised field, a shaped band around the field, and an integral tongue to fit the panel groove in the frame members. The profile contour and the reveal width varies. All tools have 1/2" shanks. Must be used in a table-mounted 3+ horsepower router and run at reduced speed. Use these bits for panels with curved edges. Multiple passes recommended. Maximum RPM 20,000.

Amana Tool ® 54119 Carbide Tipped Cove Raised Panel 1-9/16 Radius x 3-3/8 Dia x 1/2 x 1/2 Inch Shank

Create raised panels for cabinet doors, frame-and-panel furniture, and architectural paneling with a raised-panel bit. The cutter forms a fillet to delineate the raised field, a shaped band around the field, and an integral tongue to fit the panel groove in the frame members. The profile contour and the reveal width varies. All tools have 1/2" shanks. Must be used in a table-mounted 3+ horsepower router and run at reduced speed. Use these bits for panels with curved edges. Multiple passes recommended.

Amana Tool ® 54121 Carbide Tipped Ogee Raised Panel 7/8 Radius x 3-3/8 Dia x 9/16 x 1/2 Inch Shank

Create raised panels for cabinet doors, frame-and-panel furniture, and architectural paneling with a raised-panel bit. The cutter forms a fillet to delineate the raised field, a shaped band around the field, and an integral tongue to fit the panel groove in the frame members. The profile contour and the reveal width varies. All tools have 1/2" shanks. Must be used in a table-mounted 3+ horsepower router and run at reduced speed. Use these bits for panels with curved edges. Multiple passes recommended. Maximum RPM 14,000.

Amana Tool ® 54160 Carbide Tipped Corner Round 1/8 Radius x 7/8 Dia x 9/16 x 1/4 Inch Shank

Produce three slightly different profiles using this bit - an edge bead with or without a fillet and a full corner bead - by altering the bit extension or rolling the work piece between passes. This group of hard-to-find tools is particularly suitable for antique reproductions and restoration projects. Use in a handheld or table-mounted router.

Amana Tool ® 55400 Carbide Tipped Tongue & Groove 3/8 Kerf x 1-5/8 Dia x 3/4 x 1/2 Inch Shank Assembly for 1/2 to 3/4 Material

Cut perfectly fitted tongue-and-groove joints on stock between 1/2" and 3/4" thick with a table-mounted router and this assembly. The tool consists of an arbor with an integral shank, two identical, removable slotting cutters, and a pair of bearings. To cut tongues, sandwich one bearing between the two cutters (as in drawing A). To cut slots, mount one cutter between the two bearings (as in drawing B). Can be used on 1/2" through 3/4" thick material.

Amana Tool ® 55438 Carbide Tipped Adjustable Mission Style Straight Instile and Rail System 1-5/8 Dia x 13/64 to 1/2 x 1/2 Inch Shank Set

Bits in these sets have profile and groove or rabbet cutters and ball-bearing guide mounted on a 1/2" shank. Respacing of the components should only be necessary - using the provided shims - after the cutters have been resharpened. Guide straight cuts with the fence; use the pilot bearing only for cuts on curved rails or stiles.

Amana Tool ® RC-1045 CNC Insert V-Groove 45 Deg x 7/8 x 1/2 Inch Shank

The innovative CNC tool design uses a high grade solid carbide insert knife which allows you to get two uses out of each insert. Once the knife show signs of wear you can rotate the insert for a brand new cutting edge.